Add a vehicle or application below.


Pusher and Tag Axle Guide: How to Choose and Position the Right One

Quick answer: Choosing a pusher or tag axle comes down to five things: where it mounts on the truck, whether you need it steerable or non-steerable, your tire size, the weight capacity you need, and an accurate ground-to-frame measurement at the mounting location. We exclusively carry Link axles new, and we also stock used and salvage axles, so the models referenced below are Link's lineup — but the selection process applies regardless of brand.

Pusher vs. Tag: Where Does the Axle Go?

The terms describe mounting location relative to the drive axle:

    • Pusher axle — mounted ahead of the drive axle
    • Tag axle — mounted behind the drive axle

Both add load-carrying capacity to a truck without adding a second drive axle, but which one makes sense depends on your frame layout, weight distribution needs, and how the added axle affects turning and maneuverability.

What to Know Before You Buy an Axle

Where will the axle be mounted — ahead of or behind the drive axle? This is the pusher-vs-tag decision above, and it's the starting point for everything else.

Do you need a steerable or non-steerable axle? Steerable (self-steering) axles turn with the truck, which helps with maneuverability and tire wear at lower speeds and tighter turns. Non-steerable axles are simpler and often used where the added complexity isn't necessary for the application.

What tire size will you run on the pusher or tag axle? Common sizes include 215/75R 17.5, 225/70R 19.5, and 255/70R 22.5 (the most commonly used). This matters because tire size determines the loaded radius used to calculate the correct mounting bracket.

What weight capacity do you need? Common capacities include 8K, 10K, 13.5K, and 20K steerable, or 20K non-steer. One of the most frequently selected configurations is a 13.5K steerable axle, but the right capacity depends on your actual load requirements.

What's the measurement from the ground to the bottom of the frame at the mounting location? Measure in 1/2" increments. If the truck has air ride suspension, the air suspension needs to be inflated before measuring. If it has spring suspension, account for some spring sag in your measurement — an uncompressed reading will be off once the truck is loaded.

Steerable vs. Non-Steerable: Matching Capacity to the Job

Link offers both steerable and non-steerable configurations across a range of capacities:

    • Steerable: 8K, 10K, 13.5K, and 20K options
    • Non-steerable: 20K option

Steerable axles add maneuverability at the cost of some added mechanical complexity, so they tend to make the most sense where the truck regularly navigates tight turns or job sites. For full specifications on either type, Link's application guides are a useful reference: steerable options and non-steerable options.

Measuring for the Right Bracket Kit

Once you know your suspension type and tire size, three numbers determine the correct bracket kit:

    1. Which suspension you're using (steerable or non-steerable)
    2. Ground-to-bottom-of-frame height at the mounting location
    3. Loaded radius of the tire you're running (available on the tire size chart in the application guide)

Together, these determine the bracket kit that centers the axle between the ground and the frame for the correct, optimum ride height. Getting this measurement right the first time matters — an incorrect bracket kit means the axle won't sit at the height it's designed for, which affects both load distribution and tire wear.

Positioning a Pusher Axle: Federal Bridge Law Spacing

Axle spacing isn't just a mechanical question — it's a legal one. Federal Bridge Law sets a minimum spacing distance between axles, and state or local regulations may add additional requirements on top of that, so always check the rules for your specific region before finalizing placement.

For a Link steerable pusher axle, here's the general approach:

    1. Measure from the center of the rear axle forward 10', and mark that point on the frame.
    2. Your pusher axle will mount 26-1/4" behind that mark, which gives you an 8'2" spread.
    3. If you want a 9' spread instead, measure forward 11' from the center of the rear axle instead of 10'.

As the diagram shows, an install dimension of 121" achieves a 97" minimum distance as defined by federal bridge code, with the auxiliary suspension positioned relative to the existing suspension accordingly.

Always confirm current federal, state, and local requirements for your specific area before finalizing axle placement — bridge law spacing requirements can vary and are subject to change.

Tips From Our Team

Over the years, we've found the axle installs that go smoothly are the ones where the measurements are taken carefully and in the right condition, not rushed to get a number down. A few things we recommend:

    • Inflate air suspension (or account for spring sag) before measuring ground-to-frame height — a measurement taken in the wrong condition throws off the whole bracket calculation.
    • Confirm your tire's loaded radius from the actual application chart rather than estimating — it's a key input into which bracket kit fits correctly.
    • Double check your Federal Bridge Law spacing calculation against your specific region's requirements before finalizing placement, since local and state rules can add to the federal minimum.
    • If you're not certain whether steerable or non-steerable fits your application better, think through how tight the turns are where the truck operates most often — that's usually the deciding factor.

Pusher and Tag Axles at Vander Haag's

We carry Link axles new, but we also stock used and salvage axles for customers looking for a more budget-friendly option. Matching the right axle, bracket kit, and placement to your specific truck is exactly the kind of detail our team works through with customers regularly. Reach out to your local Vander Haag's location and we'll help you work through capacity, mounting position, and bracket sizing before you order.


Frequently Asked Questions

What's the difference between a pusher axle and a tag axle? A pusher axle mounts ahead of the truck's drive axle, while a tag axle mounts behind it. Both add weight-carrying capacity without adding a second drive axle; the right choice depends on your frame layout and weight distribution needs.

Do I need a steerable or non-steerable auxiliary axle? Steerable (self-steering) axles turn with the truck, which helps with maneuverability and tire wear in tighter turns, while non-steerable axles are simpler. Trucks that regularly navigate tight turns or job sites tend to benefit more from a steerable axle.

How do I know what bracket kit I need for a pusher or tag axle? The correct bracket kit depends on three factors: your suspension type (steerable or non-steerable), the ground-to-frame height at the mounting location, and the loaded radius of your tire. These three numbers together determine the bracket kit that centers the axle at the correct ride height.

How far does a pusher axle need to be from the drive axle? Federal Bridge Law sets a minimum spacing distance between axles, and state or local laws may add further requirements. For a Link steerable pusher axle, measuring 10' forward from the center of the rear axle and mounting 26-1/4" behind that point gives an 8'2" spread; always confirm current requirements for your specific region before finalizing placement.

Should I measure for a pusher axle with the suspension loaded or unloaded? Neither exactly — for air ride suspension, the system should be inflated before measuring. For spring suspension, account for some spring sag in your measurement, since an uncompressed reading won't reflect how the truck actually sits in use.



Written by the Vander Haag's Technical Team

Published: September 4, 2026
Over 85 years of industry experience
Trusted by 1,000's of independent truck owners

Related Posts All Posts

Tips




Our Locations

View Map
While Vander Haag's, Inc still holds strong to its family focused values that have been at the core of the business since first opening in 1939, the company now features 12 Midwest locations selling quality used/rebuilt/new truck parts, selling commercial trucks & trailers, and providing full service heavy duty truck repair. 43.178044 -95.155024  Spencer, IA 41.640436 -93.584249  Des Moines, IA 43.594099 -96.709450  Sioux Falls, SD 41.158006 -95.826804  Council Bluffs, IA 39.065417 -94.498172  Kansas City, MO 41.033283 -86.596167  Winamac, IN 39.740696 -86.255676  Indianapolis, IN 39.960151 -83.366700  London, OH 38.176011 -85.750102  Louisville, KY 32.807028 -96.873557  Dallas, TX 38.751480 -90.470276  Bridgeton, MO 32.219513 -98.188389  Stephenville, TX

Connect